The Art of Basic Plumbing for Installing a Bathtub
The Art of Basic Plumbing for Installing a Bathtub
Blog Article
Were you trying to find additional info concerning How to Install a Bathtub Yourself?
Installing a bathtub isn't precisely rocket science, but it does require strong plumbing, woodworking, and also sometimes, tiling abilities. Replacing an old bathtub with a new one is additionally a reasonably hard project. If the old tub is conveniently easily accessible, the job can move quickly; if you have to open a wall surface to remove the old bathtub and also position the brand-new bathtub, the task is much harder. In either situation, the project is within a home handyman's abilities, although you will require an assistant to leave the old bathtub and also embeded in the new one. Ensure you have certified yourself for the task and fit attempting it. Rather than working with a professional to take over a halfway-completed task, it is much better to consider employing one before you start. Chances are you might need an expert plumber to make tube connections.
This post will certainly aid you mount a new tub in your bathroom if you have currently acquired a brand-new tub and also don't need to alter the setup of your previous water system pipes.
Your devices and also material checklist must consist of the following:
Planning for the Installment
Firstly, the sustaining structure provided with the bath must be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is important to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the taps system to stop pressure on the bath tub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make sure you use all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now prepare to be fitted in its last placement.
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, then the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain any type of water staying in the system. The process of removing the existing taps can be fairly problematic because of the limited gain access to that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a fabric prepared for the remaining water that will originate from the pipelines. As soon as the supply pipes have been removed, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming during this process. Once the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing substance.
Before carrying on to fit the new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Using the two wooden boards under its feet, put the tub in the required position. The wood boards are practical in uniformly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four small factors.
The next objective is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level and also changing the feet on the bathtub up until the level checks out level.
To install taps, fit all-time low of the outermost flexible faucet port to the suitable supply pipeline by making a compression join; then do the very same for the various other tap.
Switch on the supply of water and check all joints and new pipework for leakages and tighten them if necessary. Fill up the bathtub as well as likewise inspect the overflow outlet as well as the normal electrical outlet for leaks.
Ultimately, deal with the bath paneling as described in the supplier's user's manual. Tiling and also securing around the bathtub should wait up until the tub has been utilized a minimum of once as this will settle it right into its last setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the other end gives a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin guaranteeing that the washers are in place in between the faucet as well as the sink. Secure the faucet in place with the manufacturer given backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The previous kind should be connected to the tap finishes initially, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bath meets the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to break a rigid seal, causing the water to penetrate the wall surface between the bathroom and the tiling, causing issues with moisture as well as feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components and also installations. They are offered in tubes and cartridges, and can sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked paper or soft rope. Bear in mind to always load the bathtub with water prior to securing, to permit the activity experienced when the tub is in use. The sealant can break relatively very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally quickly offered on the market. It is advisable to fit the tiles utilizing waterproof or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious reader on How to Install a Bathtub, I imagined sharing that article was a smart idea. For those who enjoyed our page kindly be sure to pass it around. We take joy in reading our article about Tools You Need to Install a New Bathtub .
Your solution? Just a ring. Report this page